二氧化钒薄膜的低温制备及其性能研究

针对VO₂薄膜在微测辐射热计上的应用，采用射频反应溅射法，在室温下制备氧化钒薄膜；研究了氧分压对薄膜沉积速率、电学性质及成分的影响.通过调节氧分压，先获得成分接近VO₂的非晶化薄膜，再在400℃空气中氧化退火，便可制得高电阻温度系数，低电阻率的VO₂薄膜，电阻温度系数约为-4%/℃，薄膜方块电阻为R_□为100—300kΩ；薄膜在室温下沉积，400℃下退火的制备方法与微机电加工(micro electromechanic 关键词： 二氧化钒 电阻温度系数 氧分压 射频反应溅射法     

Thermoplastic poly(ester‐imide)s derived from anhydride‐terminated polyester prepolymer and diisocyanate

The phase‐separation behavior of thermoplastic poly(ester‐imide) [P(E‐I)] multiblock copolymers, (A‐B)_n, was investigated by a stepwise variation of the imide content. All the multiblock copolymers were synthesized by solution polycondensation with dimethylformamide as a solvent. P(E‐I)s were prepared with anhydride‐terminated polyester prepolymer and diisocyanates. Polyester prepolymers were prepared by the reaction of pyromellitic dianhydride and two different polyols [poly(tetramethylene oxide glycol) (PTMG) and polycaprolactone diol (PCL)]. Structural determination was done with Fourier transform infrared spectroscopy and Fourier transform NMR, and the molecular weight was determined by gel permeation chromatography. The effect of the imide content on the thermal properties of the synthesized P(E‐I)s was investigated by thermogravimetric analysis and differential scanning calorimetry. The polymers were also characterized for static and dynamic mechanical properties. Thermal analysis data indicated that the polymers based on PTMG were stable up to 330 °C in nitrogen atmosphere and exhibited phase‐separated morphology. Polymers based on PCL showed multistage decomposition, and the films derived from them were too fragile to be characterized for static and dynamic mechanical properties. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 341–350, 2004     

氟化类金刚石薄膜的拉曼和红外光谱结构研究

关键词：     

Coupled Thermo-Hydro-Mechanical and Chemical Analysis of Expansive Clay Subjected to Heating and Hydration

A fully coupled formulation combining reactive transport and an existing thermo-hydro-mechanical (THM) code is presented. Special attention has been given to phenomena likely to be encountered in clay barriers used as part of containment systems of nuclear waste. The types of processes considered include hydrolysis, complex formation, oxidation/reduction reactions, acid/base reactions, precipitation/dissolution of minerals and cation exchange. Both kinetically-controlled and equilibrium-controlled reactions have been incorporated. The total analytical concentrations (including precipitated minerals) are adopted as basic transport variables and chemical equilibrium is achieved by minimizing Gibbs Free Energy. The formulation has been incorporated in a general purpose computer code capable of performing numerical analysis of engineering problems. A validation exercise concerning a laboratory experiment involving the heating and hydration of an expansive compacted clay is described.     

磁控溅射ZnO薄膜的成核机制及表面形貌演化动力学研究

利用原子力显微镜分析了ZnO薄膜在具有本征氧化层的Si(100)和Si(111)基片上的表面形貌 随沉积时间的演化. 通过对薄膜生长形貌的动力学标度表征，研究了射频反应磁控溅射条件 下，ZnO薄膜的成核过程及生长动力学行为. 研究发现，ZnO在基片表面的成核过程可分为初 期成核阶段、低速率成核阶段和二次成核阶段. 对于Si(100)基片，三个成核阶段的生长指 数分别为β₁=1.04，β₂=0.25±0.01，β₃=0.74；对 于Si(11 关键词： ZnO薄膜 磁控溅射 生长动力学 成核机制     

Pulsed reactive crossed beam laser ablation of La0.6Ca0.4CoO3 using O: Where does the oxygen come from?

The composition of thin perovskite films, especially the oxygen content, is a crucial parameter which influences many physical properties, such as conductivity and catalytic activity. Films produced by pulsed laser deposition are normally annealed in an oxygen atmosphere after deposition to achieve a desired oxygen content. In pulsed reactive crossed beam laser ablation, no annealing step is necessary, but a fundamental question regarding this deposition technique is still open: where does the oxygen in the films come from?There are three possibilities, i.e. from the target, from the gas background, or from the gas pulse. To answer this question two experiments were performed: ¹⁸O₂ was used during the deposition process as background gas with ¹⁶O anions in the target and ¹⁶O₂ gas pulse, and a ¹⁸O₂ gas pulse with ¹⁶O from the target and background. These experiments revealed that the quantification of the oxygen origin is only possible, when no oxygen exchange occurs at the deposition temperature. The films are characterized after deposition by elastic recoil detection analysis (ERDA) to determine the ¹⁶O/¹⁸O ratio. Experiments with different oxidizing species in the gas pulse (N₂O and O₂) confirm that the oxidizing potential (N₂O > O₂) as well as the number of molecules are important.     

反应离子镀光学薄膜的微观结构分析

用反应离子镀方法制备了ＴｉＯ２单层膜及ＴｉＯ２／ＳｉＯ２多层膜，用透射电子显微镜分别观察了由反应离子镀方法及传统蒸镀法二种不同工艺制得的ＴｉＯ２单层膜及ＴｉＯ２／ＳｉＯ２多层膜的断面结构，并对ＴｉＯ２单层膜进行了喇曼分析和卢瑟福背散射分析。